How to Install Replacement Windows in Long Beach

The short version: installing a replacement window means either dropping a new unit into your existing frame (an insert, which a confident DIYer can do in a few hours) or tearing the opening back to the studs (full-frame, which is a pro job). Ninety percent of home window swaps are inserts, and the whole game comes down to one thing: setting the new window dead level and square before you drive a single screw.

Here's the part the how-to videos gloss over while a guy pops a window in like a Lego: an out-of-square install quietly voids the energy efficiency you just paid a small fortune for. The sashes won't seal, the weatherstripping won't meet, and your shiny new low-E glass leaks air around the edges. Level matters more than speed. Take the extra ten minutes.

Insert vs. full-frame: know which job you're doing

This decision comes first, because it changes everything downstream.

	Insert (pocket) replacement	Full-frame replacement
What's removed	Just the old sashes and stops	The entire frame, back to studs
When to use it	Existing frame is solid and square	Frame is rotted, or you're changing size
Time per window	~1 hour	4–6 hours (more upstairs)
DIY-friendly?	Yes, for a careful DIYer	No — hire a pro
Flashing/waterproofing	Minimal	Full, and critical

If your existing frame is rotted, out of square, or you want a bigger opening, stop reading and get a quote. Full-frame work involves the weatherproofing layer that keeps water out of your wall, and doing it wrong doesn't show up until there's mold behind the drywall. That's not a lesson you want to pay for. Everything below is the insert process, which is the one worth DIYing.

Before you start: who is allowed to do this in California

Doing it yourself on your own home is treated differently from paying someone, and the credential a paid installer needs is not the same in every state.

The classification that actually covers your windows is C-17, glazing, issued by the Contractors State License Board. A B general building license is not automatically enough: under Business and Professions Code 7057 a general cannot take a single-trade prime contract other than framing or carpentry, so on a windows-only job it needs C-17 itself or a C-17 subcontractor. The unlicensed exemption stops at a thousand dollars and never applies where a permit is required. Check the number on CSLB's Check a License.

If you hire out any part of this, look the company up before the deposit rather than after the deposit.

Tools and materials you'll need

Lay all of this out before you pull the old window. Nothing's worse than a gaping hole in your wall and a missing caulk gun.

• Tape measure and a good 2–4 ft level
• Cordless drill/driver and the screws that came with the window
• Utility knife and a stiff putty knife
• Small pry bar and a hammer
• Composite (waterproof) shims — not wood, they wick water
• Low-expansion window-and-door spray foam (not the high-expansion stuff)
• Exterior-grade silicone or polyurethane caulk, plus a caulk gun
• Fiberglass insulation or backer rod for deep gaps
• Safety glasses and work gloves
• A helper for anything over about 30 inches wide

How to install a replacement window, step by step

1. Measure the opening (three times, no joke)

Measure the width at the top, middle, and bottom of the frame, then the height at left, center, and right. Order the window to the smallest of each set. Frames are never perfectly square, and a window built to your largest measurement won't fit the tightest spot. This is done at ordering time, but confirm your unit is 1/4 to 1/2 inch smaller than the opening so you have room to shim.

2. Remove the old sashes and stops

Pry off the interior stops carefully if you want to reuse them, then lift out the bottom sash. For older double-hungs, cut the sash cords and pull the sashes and any parting beads. You're leaving the frame; you just want a clean, empty pocket. Vacuum out three decades of dust and dead spiders while you're in there.

3. Dry-fit the new window

Set the new unit into the opening from the inside and check that it fits with a little wiggle room all around. Pull it back out. This is your cheap insurance against discovering a problem while the window is half-caulked and your arms are full.

4. Lay your caulk and set the window

Run a bead of exterior caulk on the exterior blind stop (the lip the window seats against), then tip the new window into the opening from the inside, bottom first. Press it into the caulk. Have your helper hold it while you move to the next step fast, before the caulk skins over.

5. Shim and level — the step that matters most

Slide composite shims behind the frame at each fastener location, starting at the bottom corners. Get the sill dead level and both jambs plumb, checking that the window is square by measuring the diagonals — they should match. Open and close the sashes; they should glide and lock without fighting. If they bind, you're not square yet. Do not skip this to save five minutes. This is the whole ballgame.

6. Fasten it (snug, not Hulk)

Drive the screws through the side jambs, through the shims, into the existing frame. Shims behind every screw — otherwise tightening the screw bows the jamb inward and racks the window right back out of square. Snug them evenly and re-check level and operation after each one. If a sash starts to bind, back off.

7. Insulate the gap

Fill the gap between the new frame and the old with low-expansion window foam or fiberglass insulation. The keyword is low-expansion. High-expansion foam is powerful enough to bow the jambs and jam your sashes shut, which is a genuinely infuriating way to undo perfect shimming. Trim any cured foam flush with a utility knife.

8. Flash, caulk, and trim

Seal the exterior perimeter with a continuous bead of exterior-grade caulk, leaving a small weep gap at the bottom so any water that gets behind can drain out. Reinstall your interior stops or trim, caulk the interior edges, and touch up paint. Pull the shipping labels off the glass and wipe it down.

Inside or outside — and how many at once

Insert replacements get set and fastened from the inside, which is exactly why they're DIY-friendly on the ground floor: no ladder, no scaffolding, feet on your own carpet. New-construction and full-frame units with a nailing fin fasten from the outside, which is one more reason those jobs want a pro. If you find yourself needing to work from the outside on a second story, that's the universe telling you to make a phone call.

If you're doing the whole house, batch it. A two-person crew can set eight to ten inserts in a day because setup happens once. Your first solo window will eat an afternoon; by your fourth, you'll have a rhythm and wonder what you were nervous about.

When to skip the DIY and hire a pro

Here is the paragraph a how-to guide is not supposed to contain: some of these openings are not a DIY, and knowing which is the actual skill. Call a pro when:

• There's any rot. Soft, spongy, or crumbling frame wood means the problem is behind the window, not the window. Covering it up is expensive denial.
• It's a full-frame replacement. The waterproofing layer is unforgiving and hidden until it fails.
• It's a second story or hard to reach. Ladders plus glass plus gravity is a bad trade for a few hundred bucks saved.
• You want the warranty. Self-install voids the labor and water-intrusion coverage. A pro install adds a written workmanship warranty on top of the product warranty.
• The window's oversized or a specialty shape. Bay, bow, and picture units are heavy and awkward enough to need two trained people.

And if your window is only foggy between the panes or won't stay up, you may not need a new window at all — that's often a failed seal or a $20 balance, and a failed seal between the panes beats a full swap. While you're budgeting, our companion guide breaks down how much new windows actually cost so you know whether DIY savings are even worth the risk.

The bottom line for Long Beach homeowners

An insert replacement is one of the most satisfying weekend jobs a homeowner can pull off, and the difference between a good one and a drafty one is entirely in the shimming and leveling. Measure to the smallest dimension, shim behind every screw, keep it square, and use low-expansion foam. Do that and your new energy-efficient windows will seal tight and pay you back on the cooling bill for 20-plus years.

If it's full-frame, second-story, or anything involving rot, that's our lane. Long Beach Elite Windows does free, itemized measures for replacement window installation across Long Beach and the South Bay and Greater Long Beach, and we'll tell you straight whether it's a job you can DIY or one you shouldn't. Call (877) 511-5986 and we'll measure before we quote.